Dimplex DF3015 Manuale di Servizio Scaricare il pdf (Pagina 13)

taken when handling the glass.

6. Pull the front edge of the plastic Ember Bed or plastic

grate up and forward until the rear tab releases from the

ledge located at the bottom of the Mirror (Figure 6,

page 8).

IMPORTANT:Only handle the Log Set Assembly by the

Ember Bed or plastic grate.

NOTE:Log Set Assembly ts tightly into rebox, some

force may be necessary to remove.

7. Disconnect LED harness (Figure 7, page 8).

8. Set Log Set Assembly in front of rebox.

9. Loosen but do not remove the two (2) Philips screws that

clamp the Mirror in place, and swivel down so that the

clamp clears the edge of the Mirror (Figure 8, page 8).

10. Push the Mirror out from behind to clear the frame and

remove.

11. Remove the 14 screws that attach the top panel to the

rebox. There are: one (1) screw on either side of the

Purire™ lter; two (2) on each side; and a total of eight

(8) on the top panel (Figure 11).

CAUTION:Internal wiring and colors may not be the

same within the unit being serviced as those shown. To

avoid damage to the unit, damage to property or personal

injury, ensure wires are reconnected to match their

original locations.

16. Feed Antenna wire through rubber housing and out the

back corner of the rebox.

17. Follow steps 1 through 12 in reverse order to re-

assemble the rebox.

HeaterAssemblyandCutout

Replacement

If the replace was operating prior to servicing allow at least

ve (5) minutes for light bulbs and heating element to cool off

to avoid accidental burning of skin.

Disconnect power before attempting any maintenance or

cleaning to reduce the risk of electric shock or damage to

persons.

ReplacementProcedure

1. Remove the rebox from the mantel.

2. Remove the 14 screws that attach the top panel to the

rebox. There are: one (1) screw on either side of the

Purire™ lter; two (2) on each side; and a total of eight

(8) on the top panel (Figure 11).

3. Remove top panel and Purire™ lter (lift lter straight up

and out of rebox).

4. To replace Cutout only:

i) Remove the one (1) small Phillips screw that attaches

the Cutout to the Heater Assembly as shown in

Figure 13.

Figure 11

Screws to Remove

Top View

12. Remove top panel.

13. The Remote Control Receiver board is fastened to the

back, right hand corner panel of the rebox by seven (7)

mounting studs (Figure 12). Squeeze each mounting

stud’s clasp to release the circuit board from the rebox.

NOTE: If mounting studs are damaged, replacement

mounting studs will need to be inserted from the outside

of the rebox. It is recommended to attempt to release

the receiver board without cutting mounting studs.

14. Properly orientate the replacement Remote Receiver

board and push it onto the seven (7) mounting studs until

the clasps of the mounting studs snap the board into

place.

15. Disconnect one of the wire leads from the original control

board (which are still connected to parts within the

rebox) and immediately connect it to the new control

board’s terminal, matching its position. Continue with the

remaining two (2) wires and ve (5) cable connectors,

using the same procedure.

Figure 12

Antenna wire

5 color cable to

Flicker Motor

Cable connector to

upper and lower light

harness

Cable connector

to Log Set LED

harness

4 wires to Heater

Assembly

①

②

③

①

②

③

Red wire to Main On/Off Switch

White wire to Cutout

Black wire from power cord

Mounting studs (7)

1 2 ... 8 9 10 11 12 13 14 15

Commenti su questo manuale

Nessun commento

Dimplex DF3015 Manuale di Servizio Pagina 13

Commenti su questo manuale

Prodotti e manuali riguardandi Camini Dimplex DF3015